tx site down?

[rory2005]

hi guys is the team xecuter forums and main site down for anyone else?

just keep getting 403 forbidden!

[billysastard]

hi guys is the team xecuter forums and main site down for anyone else?

just keep getting 403 forbidden!

working for me


Welcome to the Team Xecuter.


If this is your first visit, we recommend that you register (http://team-xecuter.com/forums/register.php) as you have limited access to the support forums. Click the register link to proceed.

To start viewing messages, select the forum that you want to visit from the selection below.

If you are looking for Xbox 360 Product Information you may want to first visit the MAIN PAGE (http://team-xecuter.com/forums/www.team-xecuter.com)

[/URL] (http://team-xecuter.com/forums/www.team-xecuter.com)[URL="http://team-xecuter.com/forums/www.team-xecuter.com"]

[rory2005]

cheers mate must be my isp then

[billysastard]

cheers mate must be my isp then

try getting in through google, that sometimes works for me on sites that are playing silly.

[rory2005]

still not working tried , chrome, firefox ,ie9

[garyopa]

Works for me also.

[billysastard]

still not working tried , chrome, firefox ,ie9

dunno abou those but it works on srware iron and xb tor browser both with and without vpn running so it must be are you sure you arent banned? or can you try a dns lookup and access directly by its ip addy?

[rory2005]

ive apparently upset uber top admin because i said ck3 reseller had poor coms, i was wrong to put it on the tx site but anyway i can access site behind a proxy but i cant login, plus ive found one or 2 of my posts and if your banned it normally says banned under your name.

[saleem]

theres a ck3 seller i bought from may many a time,i just recieved my first coolrunners today from them and since they only was out a week ago here i think thats good.communication i have never had to take up with them but,order wise they are bang on,i cant say anything bad only good.

so now i have to knock up a couple of leads for programming the coolrunners etc etc and then i am going to take one for a trial run on a console i have then people will no doubt hear from me.
:)

[saleem]

just went to team xecuters site a couple mins ago and all i get is the hosting service page and now its showing like its unkown.

think the hosts are having probs.
:)

[rory2005]

ta saleem, i got sick and tired of waiting for cables and quick solder boards. made my own cables, have done 2 falcons and a jasper, word of warning with jaspers - they need a cap 68nf adding between A and ground or the glitch time will take forever.

as for ck3 the problems there a thing of the past, but still prefer modtraders.

still cant get on team x site unless behind a proxy and admin teajunkie cant help.

[saleem]

so happens that my ck3pro is a bit toatsed as i knacked the usb connector up on it (common prob) so now the thing wont register with the pc,so now i cant programme the nandx so i cant programme the coolrunners,so need to buy new ck3i kit,i made all the wires to find out today that nandx HAS to have nadpro 3 wriiten to it for programming coolrunner.so now i am stuck for a while as the suppliers dont seem to have the ck3i and mrmodchips i dont trust full stop.

but at same time i think i am going to grab the official leads from tx,then it will eliminate any probs i might incur as the ones i knocked up are a bit ghetto.
:eek:

[rory2005]

lol, a lot of people even with the ck3i to nand x official cables are having problems programming the v3 hex to the nand x, getting autobaud errors.

i believe we in the uk are not getting the proper cables or qsbs till end of next week, 3 weeks after the coolrunners

[saleem]

i got notification from a site they had a small quantity of ck3i,didnt hesitate to buy from them.so hopefully when i get it i might be ok with the cables i knocked up.i have to solder the cable from the ck3i to the nand x to programme it as i cant track a connector down.and i did a pretty nifty (even though ghetto) coolrunner programing cable but whther it works time will tell.
:eek:

[rory2005]

i soldered to the solder points with the port still attached for programming the coolrunners, bought a header port that was too big cut it down to six pins and it works a treat, makes me laugh year and a half ago i couldnt solder at all now i can micro solder, i even do sub contracting work soldering the arbiter 3 rapid fire kits for angel six on ebay.

anyway on the topic of soldering the orange wire going to the resistor point is a nightmare, due to team xecuter supplying the cables in multistrand format instead of solid core cables.

the rgh is a far more difficult install than the jtag hack. not for a novice by any means

[saleem]

sorry for edit.

i finished and done first coolrunner install and works perfect.

my prob was i did indeed have a jasper it was 16mb one,silly me didnt read the voltage ratings on rear of console duh! also i had a small wire from the nandx wiring touching something and causing some short or something.i left the wiring in for programming the nand etc.so i got exell and the rest is hitory.

thanks
:D