please help, i was coming out of factrory service mode and things have gone wrong

Discussion in 'PS3 Hardware Repairs & Problems' started by hotchef, Jan 23, 2011.

Thread Status:
Not open for further replies.
  1. 149
    0
    0
    hotchef

    hotchef New Member Loyal Member

    Joined:
    Feb 19, 2007
    Using a e3 card reader i downgraded from 3.5 to 3.41 and went to leave factory mode but it failed, the ps3 green light just keeps flashing. if i tired to start without the usb the green light goes red
    I backed up the usb card and re copied it to the usb stick and tried the last stage again
    if i use a clean usb and just file 2 and no sys text then i get this message on the PS3
    The system software cannot be run correctly. Press the PS buttonto try to restart the system
    If the system cannot be restarted, you must reinstall the system software.
    Connect storage media that contains update data of version 3.41 or later, and press the START and SELECT buttons at the same time.
    For information on how to obtain update data refer to SCE Web site for you region

    my sys.txt on the card is
    manufacturing updating start
    PackageName = /dev_usb000/PS3UPDAT.PUP
    settle polling interval success
    vflash is enabled...
    creating system regions...
    create storage region: (region id = 1)
    create storage region: (region id = 2)
    format partition: (region_id = 2, CELL_FS_UTILITY:HDD0, CELL_FS_UFS)
    create storage region: (region id = 3)
    format partition: (region_id = 3, CELL_FS_UTILITY:HDD1, CELL_FS_FAT)
    creating system regions done.
    boot from nor flash...
    creating nor flash regions...
    create storage region: (region id = 2)
    create storage region: (region id = 3)
    creating flash regions...
    create storage region: (region id = 1)
    create storage region: (region id = 2)
    format partition: (region_id = 2, CELL_FS_IOS:BUILTIN_FLSH1, CELL_FS_FAT)
    create storage region: (region id = 3)
    format partition: (region_id = 3, CELL_FS_IOS:BUILTIN_FLSH2, CELL_FS_FAT)
    create storage region: (region id = 4)
    format partition: (region_id = 4, CELL_FS_IOS:BUILTIN_FLSH3, CELL_FS_FAT)
    create storage region: (region id = 5)
    create storage region: (region id = 6)
    Initializing
    taking a while...
    start Updating Proccess
    UpMng.UpdatePackage() failure
    manufacturing updating FAILURE(0x8002f048)
    Total Elapsed time = 20255 msec

    please advise what i should do
    thanks
     
  2. 235
    0
    0
    steplay29

    steplay29 New Member Loyal Member

    Joined:
    Nov 19, 2003
    Home Page:
    if you want to leave service/factory mode put the self file form folder 2 of your downgrader files into the upgrade bit of your e3 card reader.switch of ps3 and put the e3 into your usb port far most right one.turn on ps3 green light will come on for about 10 seconds then go red.you should now be out of service /factory mode.
     
  3. 149
    0
    0
    hotchef

    hotchef New Member Loyal Member

    Joined:
    Feb 19, 2007
    Sorted thanks but should I not use e3 card reader any more

    Now I have E3 card reader working what's the advantage of soft mod with no dongle to 3.55?
     
  4. 6,300
    399
    83
    tech3475

    tech3475 Likes to Post Loyal Member

    Joined:
    Jul 2, 2007
    The only advantage is that you may get a couple more days on PSN and you dont need to resign games to work from the HDD (assuming they work).

    edit:

    are you on 3.5 still or have you downgraded? If you have already downgraded the above still applies, otherwise I would stay with 3.5 for now since downgrading has BD issues on certain models.
     
    Last edited by a moderator: Jan 28, 2011
Thread Status:
Not open for further replies.

Share This Page