Discussion in 'PS3 Modding Tutorials' started by pepe, Aug 27, 2012.
Maybe we can qa flag in dex 3.55. I don't know... If there is no dex 4.30, I will do this.
for step 6 do i put the firmware in the update folder or just put on flash drive. cause i put it in update folder & i did step 8, & its been blinking for more then 20mins. Can i redo if i messed up on step 6 ?
anyone know a place to get a cheap usb dongle without using the moeny transfer
damn i think it bricked, now it make a weird multi-beeping noise
took all day but fixed brick & made it back to 3.55
hi KoolKid2K4, you did it with the 256 MB nand ?
need the 239 MB NAND
What did you do to fix yours? my unit is still stuck.. waiting for my e3 card reader to come..
I´ve followed the guide until step 8.
When I run FSM it just beeps three times and boots into XMB mode again.
Now I´m not sure what my options are.
Is it possible to flash back my DEX.NORBIN to console. I haven´t booted it yet.
Log from FSM:
firmware version detected: 0x8aac (35500)
SUCCESS: read EPROM
ERROR: failed to write to EPROM
ERROR: SS EPROM write error: 80010505, mode: ff
factory/service mode failure!
I want to avoid data loss during FSM flashing. If I replace the HDD just for the flashing process, will my other HDD work again with all the data accessible? Thanks.
not sure which nand i had, but i used my teensy board & psgrade payload to get into service mode. i put the renamed Rogero CFW V3.4 in the root of flashdrive (not update folder) look up tutorial on the psgrade downgrade
if you make it to Rogero & you get out of factory mode & you try to update to lower cfw from xmb ( cfw 3.55 kmeaw) it will give you red screen when updating. redo the factory mode but this time place kmeaw 3.55 in the root of flashdrive instead of rogero. my ps3 was then able to complete the update process. after that do the Dehash tutorial.
Can i use OFW 3.55 in place of CFW Rogero v3.4 using this tutorial to convert DEX>CEX ?
Can someone please answer this? I have the same question.
Always risk semi-brick if you didnt QA on cex beforehand.
Now I'm on DEX 4.21 and have a little afraid to go back to CEX because I've done conversions from REBUG 3.55.2 OTHEROS++ (update package 0.7) without wipe my linux region and never use qa_flag.pkg. I have my CEX NOR backup, 355 downgrader PUP, OFW 355 DEX PUP, ROGERO DEX 355, I know how to write to flash with multiman but I don't want to (semi)brick my PS3. And don't want to erase my HDD (because of linux) using FSM method..
if someone was successful conversion from a similar configuration?
I think to use 999 downgrader from Rebug after write CEX.NOR with MM from Rogero 3.55 and install 999 downgrader from recovery. (of course, if the console boot up)
ask for suggestions
im on a slim and i went to switch from dex to cex and what i did was i went to multiman and double clicked my cex norbin and then i quit and went to xmb then i held the ps button and shut down then i turned it back on with flashdrive in right usb with ps3 folder on root then update then regeros 3.8cfw as ps3updat.pup and i turned console on and all i get is a beep boop beep boop beep boop and it shuts off ... what can i do PLEASE HELP
look up tutorial on the psgrade downgrade
I have a slim ps3 what if I don't have a copy of cex.norbin to use to convert my dex console back?
Separate names with a comma.